Livingston Avenue Bridge

Livingston Avenue Bridge
Coordinates	42.65431°N 73.741777°W / 42.65431; -73.741777 (Livingston Avenue Bridge)
Carries	Amtrak, CSX and CP Rail
Crosses	Hudson River
Locale	Albany and Rensselaer, New York
Other name(s)	North Bridge or Hudson River Bridge
Owner	CSX Transportation
Characteristics
Design	Pratt through truss with swing span
Total length	1,272 feet (388 m)
Longest span	259.9 feet (79.2 m)
No. of spans	1 truss swing span, 4 truss spans, 4 girder spans
Rail characteristics
No. of tracks	2
History
Constructed by	New York Central Railroad
Fabrication by	American Bridge Company
Construction start	1901
Opened	1902
Statistics
Daily traffic	12 Amtrak passenger trains and 2–6 freight trains (as of 2024)
Location
References
BridgeHunter.com

The Livingston Avenue Bridge is a railroad bridge over the Hudson River in New York connecting Albany and Rensselaer. The original structure was built in 1866 by the Hudson River Bridge Company but was replaced in 1901–02. A rotating swing bridge span allows large ships to proceed up the river.

The New York State Department of Transportation (DOT) has identified the bridge as a critical link in its Empire Corridor passenger rail line, and has initiated a study project for bridge rehabilitation or replacement.

Operation

The bridge was purchased from CSX in December 2012 as part of Amtrak's Empire Corridor lease. The lease grants Amtrak ownership and control over the bridge and adjoining 100 miles of track, extending east from Hoffmans, NY to Albany-Rensselaer station; then south to MP 75, just north of Poughkeepsie, NY. A small branch extends east from Albany-Rensselaer station down the Post-Road subdivision, where Amtrak's ownership terminates just south of the Interstate 90 Berkshire Spur overpass. The Livingston Avenue Bridge is most frequently used for east-west travel in New York, as well as freight trains of CSX and CP Rail. The bridge hosts an active railroad interlocking tower and Amtrak block operators staff the tower 24 hours a day. They are responsible for directing rail traffic around Amtrak's Rensselaer Terminal and nearby trackage as well as opening and closing the bridge. Due to the deteriorated condition of the bridge, trains cross one at a time at 15 miles per hour (24 km/h). DOT considers the swing bridge mechanism to be unreliable and the overall bridge design inadequate for current railroad operating standards. The bridge opens for ship traffic about 400 times per year.

History

The original bridge in 1866

The Hudson River Bridge Company was incorporated April 9, 1856. Work on the bridge was begun in April 1864. The earlier Green Island Bridge had opened to the north in Troy in 1835, but required the longer route of the Schenectady and Troy Railroad west from Troy. The new bridge, called the Hudson River Bridge, was to connect directly to the New York Central Railroad on the west (Albany) side of the bridge and to the Hudson River Railroad, Troy and Greenbush Railroad, and Boston and Albany Railroad on the east (Rensselaer) side. The turntable bridge was 4800 feet (1500 m) long, with a clearance of 30 feet (9 m) from high water when closed.

The first engine, the Augustus Schell, passed over the bridge on February 18, 1866. Passenger trains started using it on February 22. After the Maiden Lane Bridge was constructed a bit further south, the Hudson River Bridge was used mostly for freight trains and the few passenger trains that passed by Albany but did not need to stop there. The Maiden Lane Bridge was often referred to as the "South Bridge" and the Hudson River Bridge as the "North Bridge". In the winter of 1866, once travel patterns were set, Cornelius Vanderbilt, owner of the Hudson River Railroad, suddenly refused to allow any transfers from the New York Central. According to the documentary The Men Who Built America the motivation for this closure was retaliation against the owners of New York Central for negotiating a new contract in bad faith. The New York Central board gave in, and in 1867 Vanderbilt acquired the company, and in 1869 merged it with the Hudson River Railroad to form the New York Central and Hudson River Railroad. This gave the New York Central a majority of ownership in the company. In 1900, the New York Central leased the Boston and Albany.

The current bridge was constructed in 1901-2 and was named the Livingston Avenue Bridge. The 1902 bridge was built upon the original 1866 pilings. At the time the original Hudson River Bridge was constructed, Livingston Avenue had been named Lumber Street, as it led to the Albany Lumber District.

Rehabilitation study

A tour boat heading north passes through the Livingston Avenue Bridge

As of 2012, the NYSDOT was evaluating whether to rehabilitate or replace the structure. The cost to replace the bridge was estimated at $50 million in 1998. Decisions about rehabilitation included consideration of upgrading the bridge to accommodate high-speed rail traffic. Funding for construction had not yet been allocated. One matter of contention was whether the project will restore the closed public walkway over the bridge. Doing so would greatly improve pedestrian access between Albany and Rensselaer, but the bridge owner, CSX, was citing safety concerns. In 2022, the NYSDOT will hold public meetings to discuss a project to rebuild the bridge.

The commencement of construction on the US$634.8 million, two-track replacement bridge was announced in July 2024. The new lift bridge would consist of 7 spans, be able to handle taller and heavier loads, and allow two trains to cross at the same time. Completion of construction was targeted for the summer of 2028.

See also

• List of fixed crossings of the Hudson River

References

• The Albany Railroad Bridge, Harper's Weekly 1866
• The Bridge at Albany, New York Times February 24, 1866, page 1
• AllOverAlbany.com. "The Livingston Avenue Bridge." 2011-02-28.

External links

Media related to Livingston Avenue Bridge at Wikimedia Commons

• Livingston Aveneue Bridge Project | NYSDOT